If debris is difficult to remove, consult your Yamaha dealer. Check for any deterioration or damage to the throttle cable. Take note of weather forecasts and the prevailing weather conditions before setting out on your watercraft. Once you download your manual it is yours forever. Do not operate the watercraft when the total weight exceeds 240 kg 530 lb including any cargo. El uso de otro aceite puede dañar gravemente el convertidor catalítico y otros. Fuel breather hose Fuel tank assembly Hose clamp Fuel filler hose Hose clamp Fuel sensor assembly.
Flywheel magneto removal and installation 1. The spark plug cap and ignition coil are integrated. Starter clutch assembly inspection 1. A fire extinguisher is not standard equip- ment with this watercraft. Both of you should alter course to could lead to a collision unless the Steering avoid an accident.
Recommended grease: Yamaha marine grease, Yamaha grease A Water resistant grease 6. Then, sand the scratches once again with 600 grit sand- paper either wet or dry. Immediately after inspection, lubricate the bearings to prevent rust. Check the ground line of the starter relay switch. Piston pin and bearing inspection 1. Clean around the spark plug bases with compressed air before removing the plugs, and be sure that no debris is allowed to enter the combustion chamber and remove the spark plugs.
To close the hood, push the hood down to lock it in place. Inspeccione: Hauptdüse Gicleur principal Surtidor principal Steuerdüse Gicleur de ralenti Surtidor piloto Corps de carburateur Vergasergehäuse. Use to drain water in the bilge when the water- 4 Speed sensor craft is on dry land. Pinion gear Reverse the disassembly steps for assembly. Instale: Reniflard de la batterie 1 Batterie-Entlüftungs- Manguera de ventilación de la Batterie schlauch 1 batería 1 Câble positif de la batterie 2 Batterie Batería Fil négatif de la batterie 3.
Install: Intermediate drive shaft Distance a: 9. Perform the same lubrication procedure for joint hole. Überprüfen: Inspección de la línea de aceite Ölfilter Filtre à. Starter Relay Switch Operation Inspection 4. Water temperature sensor resistance: 0 ˚C 32 ˚F : 24. Shut the engine off by removing the clip from the engine shut-off switch. Alle Kabelverbindungen sind korrekt hergestellt.
It should be smooth over the complete range, and spring back to the idle position when released. This could deform or loosen the cable end due to extreme angles and or pressure. The fuel filter should be replaced once a year or after every 200 hours of operation, or if water is found in the filter. So visit your authorized Yamaha dealer to get all the facts. If the mechanism does not work properly, have a Yamaha dealer service it.
Release the throttle lever to decrease engine speed or to return it to the idle posi- tion. You must decide whether to wear a hel- met while you ride for recreation. Extraiga y instale: Angetriebene Kopplung Accouplement mené. There are no incorrect wiring connections. Um das Eindringen von Was- 2.
From full speed, the watercraft comes to a complete stop in approximately 110 m 360 ft after the throttle is released and the engine is stopped, although this dis- tance will vary depending on many factors, including gross weight, water surface condi-. . This cancels the process of setting a code. Verbindungsstücke trennen und etwas Schmierfett auftragen. When the engine is running, cooling water is circulated in the engine, and then it is discharged from the pilot outlets. Oil hose Bolt Tank belt Oil tank assembly Hose clamp Oil filler hose Oil level sensor Reverse the removal steps for installation. O-ring Not reusable Bolt Starter motor front cover O-ring.
Hot water and steam spurt- ing from exhaust outlet into the air can cause serious burns. Screw Fuel pump cover Gasket Not reusable Diaphragm O-ring Diaphragm body 4-26. Apply battery voltage to the starter motor directly. Graisse recommandée: Grasa recomendada: Graisse maritime Grasa náutica Yamaha, Yamaha, graisse grasa A Yamaha Empfohlenes Schmier- Yamaha A Grasa hidrófuga mittel: graisse hydrofuge Yamaha Marine Fett, 6. Fuse holder continuity: Between 1 and 2 Between 2 and 3 2. This may enlarge the jet diameters and seriously affect performance. Gasoline vapor is explosive if ignited.
If idle speed increases, check the throttle lever free play and the throttle cable connection. Water- Be informed about boating safety. Hose clamp Disconnect the oil filler hose from the oil filler neck. Check the impeller seal for cracks or damage. Boarding in deep water requires more skill. If the watercraft must be towed in an emergency using a tow line, the operator should ride the watercraft, holding onto the handlebars. Clearance a Shim thickness 0—0.