2006 2008 kawasaki er 6n er 6n abs factory service repair manual. 2006 2019-03-18

2006 2008 kawasaki er 6n er 6n abs factory service repair manual Rating: 9,3/10 243 reviews

KAWASAKI ER

2006 2008 kawasaki er 6n er 6n abs factory service repair manual

Guide Hold the intake air pressure sensor lead. Never touch a hot engine. Front Brake Light Switch 12. The initial maintenance is vitally important and must not be neglected. Immediately wipe any spilled coolant from tires, frame, engine or other painted parts. Using another air cleaner element will wear the engine prema- turely or lower the engine performance. Do not remove the radiator cap or attempt to change the coolant when the engine is hot; allow it cool completely.

Next

Reading : 2006 2008 Kawasaki Er 6n Er 6n Abs Factory Service Repair Manual

2006 2008 kawasaki er 6n er 6n abs factory service repair manual

Stick coil trouble Inspect see chapter 16. Toothed Washer, 34 mm 1. Other- wise, the motorcycle can not clear the regulation. Run the main harness inside the ribs on the air cleaner housing cover. Repair methods may vary slightly from make to make. Main Fuse 30 A 9.

Next

KAWASAKI Motocycle Manuals Resource: Kawasaki ER

2006 2008 kawasaki er 6n er 6n abs factory service repair manual

The headlight comes on after the starter button is released and stays on until the ignition switch is turned off. Also, replace the steel plates if their teeth are damaged. Torque - Breather Plate Bolts: 9. Fix the brake hose rear brake reservoir tank ~ rear master cylinder to the frame with the clamps. Never reuse old brake fluid. Fix the clamp to the bracket. If whitish cotton-like wafts are observed, aluminum parts in the cooling system are corroded.

Next

Reading : 2006 2008 Kawasaki Er 6n Er 6n Abs Factory Service Repair Manual

2006 2008 kawasaki er 6n er 6n abs factory service repair manual

Headlight Fuse 15 A 2. Replace the caliper if the cylinder and piston are badly scores or rusty. Torque - Neutral Switch Holder Screw: 4. Intake air temperature sensor trouble Inspect see chapter 3. If any wiring is poor, replace the damaged wiring. Intake Air Pressure Sensor 3. Striking the rotor can cause the magnets to lose their magnetism.

Next

Reading : 2006 2008 Kawasaki Er 6n Er 6n Abs Factory Service Repair Manual

2006 2008 kawasaki er 6n er 6n abs factory service repair manual

Run the reserve tank overflow hose between the air suction valve cover and the stick coil. Therefore, it should be handled carefully, never struck sharply, as with a hammer, or allowed to fall on a hard surface. Direction of Engine Rotation When rotating the crankshaft by hand, the free play amount of rotating direction will affect the adjustment. Standard: Link Pin Length Standard:. Run the left city light lead through the clamp and locate its connector in front of the main harness. Seat Height 805 mm 31.

Next

Reading : 2006 2008 Kawasaki Er 6n Er 6n Abs Factory Service Repair Manual

2006 2008 kawasaki er 6n er 6n abs factory service repair manual

Main Fuse 30 A 3. Do not touch the spark plug, ignition coil or ig- nition coil lead while the engine is running, or you could receive a severe electrical shock. If the oil leakage is found on it, replace the shock absorber with a new one. Ball Bearing and Needle Bearing Do not remove pressed ball or needle unless removal is absolutely necessary. If the clearance is between 0. Torque - Water Pump Drain Bolt: 9.

Next

2006

2006 2008 kawasaki er 6n er 6n abs factory service repair manual

Fix the clamp to the bracket. Such a shock to the sensor can damage it. . Do not loosen the leads in this area. Main Fuse 30 A 7. Oxygen Sensor Equipped Models 9. Then tighten them according to the specified se- quence to prevent case warpage or deformation which can lead to malfunction.

Next

KAWASAKI Motocycle Manuals Resource: Kawasaki ER

2006 2008 kawasaki er 6n er 6n abs factory service repair manual

Forcibly prying off the seal cap to add water is very dangerous. Fix the starter relay to the ribs on the battery case. Battery 12 V 10 Ah 7. Example: Present shim is 2. Remove the oxy- gen sensor see Oxygen Sensor Removal in the Electrical System chapter.

Next