Ford ranger 2009 workshop repair service manual 9734 complete informative for diy repair 9734. FORD RANGER MAINTAINCE AND REPAIR MANUAL Pdf Download. 2019-02-17

Ford ranger 2009 workshop repair service manual 9734 complete informative for diy repair 9734 Rating: 5,9/10 1401 reviews

2009 Ford Ranger Auto Repair Manual

ford ranger 2009 workshop repair service manual 9734 complete informative for diy repair 9734

Remove the pushrods, keeping them in order so they may be installed in their original locations. The washers must be installed in their original positions, so keep track of them. Remove the jack and jackstands and lower vehicle. To install: Thoroughly clean all gasket mating surfaces. The labels can usually be ordered from a local dealer. Next check the free length and squareness of each spring. Remove the accessory drive belt.

Next

2009 Ford Ranger Auto Repair Manual

ford ranger 2009 workshop repair service manual 9734 complete informative for diy repair 9734

Discard the clip and remove the inner race assembly. Align the air bleed hole on the thermostat with the notch in the housing, which is also the 12 o'clock position Clean all mating surfaces thoroughly. Install rocker arm shaft assembly to the cylinder head and guide adjusting screws on to the pushrods. Remove the accessory drive belt. Install the air cleaner outlet tube, then tighten the outlet tube clamps until snug.

Next

Download Ford Expedition 2009 Workshop Repair Service Manual 9734 Complete Informative For Diy Repair 9734 Ebook PDF 2019 PDF E

ford ranger 2009 workshop repair service manual 9734 complete informative for diy repair 9734

Install the spark plug wires. However, if you decide to tow a trailer, using the prior equipment is a must. Reconnect the harness connector to the switch. Get access to our 2009 Ford Ranger repair information right now, online. All of the journals should be perfectly round and smooth.

Next

Download Ford Ranger service and repair manual free pdf

ford ranger 2009 workshop repair service manual 9734 complete informative for diy repair 9734

However, it is not necessarily the best, and in some cases, a knurled valve guide will not stand up for more than a short time. © 2004 Thomson Delmar Learning. Apply sealing compound to the joining surfaces of the upper and lower intake manifolds. It is incorporated with the high mount brake light. Position a piece of wood on a floor jack and raise the engine carefully as far as it will go. This is the friction between the bearing surface of the bolt head, screw head or nut face and the base material or washer the surface on which the fastener is rotating. Raise and support the vehicle safely.

Next

FORD RANGER MAINTAINCE AND REPAIR MANUAL Pdf Download.

ford ranger 2009 workshop repair service manual 9734 complete informative for diy repair 9734

Install the valve covers using new gaskets. If the assembly goes bad, it must be replaced as an entire unit. Anytime the torsion bar is disturbed, the ride height must be checked and adjusted. Upper intake manifold removal on the 2. Tread wear indicators will appear when the tire is worn Accurate tread depth indicators are inexpensive and handy You can check your own tread depth with an inexpensive gauge or by using a Lincoln head penny. If the measured resistance is greater than 7000 ohms per foot, the wire is defective and should be replaced. There should be no odor of fuel as well.

Next

Download Ford Expedition 2009 Workshop Repair Service Manual 9734 Complete Informative For Diy Repair 9734 Ebook PDF 2019 PDF E

ford ranger 2009 workshop repair service manual 9734 complete informative for diy repair 9734

Remove the two bolts that retain the fan shroud and position the shroud back over the fan. Follow the service procedures under Oil Pan Removal and remove the oil pan assembly. Remove the switch from the transmission. Once the belt is installed, take another look at all the pulleys to double check your installation. Remove the vacuum diaphragm retaining clamp bolt and clamp.

Next

FORD RANGER MAINTAINCE AND REPAIR MANUAL Pdf Download.

ford ranger 2009 workshop repair service manual 9734 complete informative for diy repair 9734

The resultant wiring would hold the correct firing order, but could change the relative placement of the plug towers in relation to the engine. At the extreme ends of lever travel, the door should be heard to firmly seat, indicated by a loud thumping sound, allowing either maximum or no air flow through the heater core. Remove the snaprings that retain the bearing cups. Relieve the fuel system pressure. Small parts such as the valves, springs, etc. To install: Ensure that all of the gasket mating surfaces are clean and free or grease, oil or dirt. Refer to the necessary service procedures in this section.

Next

2009 Ford Ranger Auto Repair Manual

ford ranger 2009 workshop repair service manual 9734 complete informative for diy repair 9734

This will prove fatal in sufficient quantity. Disconnecting the start wire at the starter relay will cause the ignition control module to revert to Start Mode timing after the vehicle is started. The castellations on the retainer must be in alignment with the cotter pin holes in the spindle. Damage to the sealing surfaces could result and cause a leak. Hold the regulator in one hand and pry off the cap covering the Aterminal screw head with a small prybar.

Next