Kawasaki kx250 full service repair manual 2003 2005. Kawasaki KX250F Service Repair Manual 2019-01-28

Kawasaki kx250 full service repair manual 2003 2005 Rating: 7,6/10 207 reviews

Kawasaki KX125

kawasaki kx250 full service repair manual 2003 2005

Change the coolant in accordance with the Periodic Maintenance Chart see Periodic Maintenance chapter. Adjust the tire air pressure to suit track conditions and rider preference, but do not stray too far from the recom- mended pressure. Do not disassemble the cylinder unit. Lubricate the drive chain if it appears dry. Overall Height 1 265 mm 49.

Next

Kawasaki KX250 service Workshop Service Repair Manual

kawasaki kx250 full service repair manual 2003 2005

Torque - Subexhaust Valve Cover Bolts: 8. A dirty or improperly oiled element can diminish engine performance, cause spark plug fouling, and could affect long term durability of the engine. When air enters the brake lines, brake lever or pedal movement will be partially used in compressing the air. Press the bearing into place by putting pressure on the correct bearing race as shown. If there is any irregularity, replace the drive chain.

Next

2004

kawasaki kx250 full service repair manual 2003 2005

Also, coat the base where the lip of the element fits. Change the coolant in accordance with the Periodic Maintenance Chart. Special tools, gauges, and venient operation. Torque - Rear Sprocket Nuts: 34 N·m 3. Often, the tightening sequence is followed twice initial tightening and final tightening with torque wrench. Never reuse old brake fluid.

Next

Kawasaki KX250F Service Repair Manual

kawasaki kx250 full service repair manual 2003 2005

Increasing the float height lowers the fuel level and decreasing the float height raises the fuel level. If there are notches worn into the splines, replace the clutch hub. This can damage or warp the disc. Chain 20-link Length 323 mm 12. If they are worn as illustrated or damaged, replace the sprocket. The standard piston-to-cylinder clearance must be adhered to whenever the cylinder is replaced. Torque - Caliper Mounting Bolts: 25 N·m 2.

Next

Kawasaki KX250F Service Repair Manual

kawasaki kx250 full service repair manual 2003 2005

Special Tool - Top Plug Wrench, 46 mm: 57001-1622 Torque - Base Valve Assembly: 27 N·m 2. If only a piston is replaced, the clearance may exceed the standard slightly. Make sure the area is well-ventilated and free from any source of flame or sparks;. Any damaged parts should be replaced with new ones. It Cylinder head warped is meant simply as a rough guide to assist Cylinder base gasket damaged the troubleshooting for some of the more Read valve damaged. Replace with new ones whenever removed. Shock Absorber Spring Free Length Standard: 260 mm 10.

Next

2004

kawasaki kx250 full service repair manual 2003 2005

I Unit Mounting Bolts 0. Learn and ob- serve all the rules below. . However, an ohmmeter cannot detect layer shorts and shorts resulting from insulation breakdown under high voltage. Chang- ing the rear brake fluid is the same as for the front brake.

Next

Kawasaki KX250F Service Repair Manual

kawasaki kx250 full service repair manual 2003 2005

Wheelbase 1 480 mm 58. They must be smooth and clean for the radiator cap to function properly. Do not clamp the axle holder too tight. If it is scratched or damaged, replace the disc. Subexhaust Valve Left Side R: Replacement Part 30. A bent fork could cause difficulty in shifting, or allow the transmission to jump out of gear when under power.

Next

KAWASAKI KX250 SERVICE MANUAL Pdf Download.

kawasaki kx250 full service repair manual 2003 2005

Tighten fasteners to the specified torque using a good quality torque wrench. Air, however, is easily compressed. Also, the throttle valve may not open fully at full throttle. Since the ball bearings are made to extremely close toler- ances, the wear must be judged by feel rather than mea- surement. Transmission Oil Level Inspection 2-26 Specifications. Such a shock to the parts can damage them. R: Replacement Parts Si: Apply Silicone grease.

Next