Allowable limit: Hand brake 13. In order to perform the work efficiently and to avoid costly mistakes, read the text and thoroughly familiarise yourself with procedures before starting work. These groups contain general information, diagnosis, testing, adjustments, removal, installation, disassembly, and assembly procedures for the systems and components. Measure the resistance between the terminals of the primary winding. Remove the cutter and check new valve seat. Caution In order to avoid the water tank rusting, please do not use the unclear trade mark refrigerant. So not screw the dipstick into engine as checking.
Shift drum fixed catch bolt Shift drum Remove shift spindle, shift fork shaft, shift fork and shift drum. It can zoom in anywhere on your computer, so you can see it clearly. Scrape gasket residues off the crankcase contact surface. Caution Tape a tightening tape onto the thread of hexagon bolt. If you get battery acid on your skin, flush it off immediately with water. First disconnect the negative cable terminal, next, the positive cable terminal.
Install pulse generator 2 screws. Remove front cushion upper bolt nut, and remove the bolt and cushion. Do not tear off stickers. Keep the vehicle on level ground and the front wheels facing straight ahead. Ensure the service book is stamped and signed. Cotter pin Universal holder Remove cotter pin and ball joint nut. This manual has detailed illustrations as well as step by step instructions.
Yamaha Outboard is overheating, overheats over heats, running hot 8. Use vacuum cleaner or other authorized tool instead. Set Installation·························· 10-8 Right Cover Bearing····························. The maintenance schedule is established by taking the monthly 1000 kilometers as a reference which ever comes first. Driven sprocket holder Inspection Check bearings on rear wheel axle bearing seat.
Comes with comprehensive details regarding technical data, diagrams, a complete list of parts and pictures. Loosen the brake hose bolt and finally remove the brake hose. In case of wear or damage contact your dealer for replacements. Install the driven pulley that has installed the belt onto drive shaft. Spring Assembly Place the fuel needle onto the throttle valve and.
Check bearings on gear box and gear box cover. Damaged throttle cable will make unstable drive-ability. It covers all the topics like: Engine, General Information, Tranmission, Chasis, Lightning , Steering, Seats System, Clutch, Suspension, Locks, Brakes, Lubrication, Electrical, Frame Fuel System, Battery and more. Caution Do not damage the matching surface of cylinder head. If oil level is nearly low level, fill out recommended oil to upper level.
The starting clutch gear should be rotated in C. Engine number is located front of the engine as shown in 2. Remove battery positive + post. Engage a brake and push the knob in and move the shift lever from N to H, L or R L Shift is used for rough surfaces Æ. Drain out the engine oil and coolant, and then remove coolant hoses.
Just print out the section you need and throw it away when you are done! Remove 3 bolts and remove drive chain protector. Motor is shifting hard 11. Replace with new front winker light bulb. Replacement of Mechanical Seal Water pump bearing Remove the inside bearing by inner bearing puller. Turn the headlight adjustment screw to adjust headlight beam high.
Never run your engine in a closed area. O-ring Spring Air cut-off valve Cover Inspection Check the valve is in normal. Check if bearings can be turned in smooth and silent, and also check if bearing outer ring is mounted on gear tightly. Use vacuum cleaner or other authorized tool instead. Remove cam sprocket bolts and then remove the sprocket by prying chain out. The trouble usually can be determined or by performing cylinder compression test and judging the abnormal noise generated. Outboard has poor deceleration 5.
This manual includes special notes, important points, service data, precautions, etc. Please always ride the vehicle with the engine oil warning light off, otherwise, it will cause damage to the engine. Please ride the vehicle with the engine oil warning light off, otherwise, it will cause damage to the engine. Hold drive face with universal holder, and then remove drive face nut. Water hoses clamp Remove coolant inlet hoses from water pump. The descriptions are brief but precise and are supported by photographs, notes, drawings and schematics, as well as exploded and sectional drawings. Water pump oil seal Special tools: driver inner Water pump oil seal driver inner Install a new outside bearing to the right Water pump bearing crankcase cover.